{"id":18645,"date":"2026-11-05T18:18:17","date_gmt":"2026-11-05T10:18:17","guid":{"rendered":"https:\/\/ruidapacking.com\/?p=18645"},"modified":"2026-11-05T18:18:20","modified_gmt":"2026-11-05T10:18:20","slug":"capsules-sticking-together-causes-solutions","status":"publish","type":"post","link":"https:\/\/ruidapacking.com\/ru\/capsules-sticking-together-causes-solutions\/","title":{"rendered":"Why Do Hard Capsules Stick Together: Storage, Humidity &amp; Filling Process Solutions"},"content":{"rendered":"<p class=\"wp-block-paragraph\">Do your hard capsules become soft and stick together in bottles or collection bins?<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Sometimes, a capsule that is rigid when discharged from <a href=\"https:\/\/ruidapacking.com\/ru\/capsule-filling-machine\/\">capsule filler machines<\/a> can become a stubborn clump when time goes by. However, in most cases, capsules can stick together in storage, during feeding, or after filling. This guide explains how humidity, static electricity, formulation properties, and machine conditions contribute to capsule sticking, then shows how pharmaceutical and nutraceutical manufacturers can investigate and prevent it.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">\u041e\u0441\u043d\u043e\u0432\u043d\u044b\u0435 \u0432\u044b\u0432\u043e\u0434\u044b<\/h2>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Where capsule sticking can start: storage, feeding, or post-filling handling.<\/li>\n\n\n\n<li>How moisture, static charge, formulation properties, and powder residue contribute to sticking.<\/li>\n\n\n\n<li>How to identify the source before changing capsule filling machine settings.<\/li>\n\n\n\n<li>How storage controls, equipment design, cleaning, and process trials help prevent recurrence.<\/li>\n<\/ul>\n\n\n<div class=\"wp-block-image\">\n<figure class=\"aligncenter size-full\"><img fetchpriority=\"high\" decoding=\"async\" width=\"960\" height=\"540\" src=\"https:\/\/ruidapacking.com\/wp-content\/uploads\/2026\/11\/Sticky-Capsules-Stuck-Together.jpg\" alt=\"Sticky Capsules Stuck Together\" class=\"wp-image-18655\" srcset=\"https:\/\/ruidapacking.com\/wp-content\/uploads\/2026\/11\/Sticky-Capsules-Stuck-Together.jpg 960w, https:\/\/ruidapacking.com\/wp-content\/uploads\/2026\/11\/Sticky-Capsules-Stuck-Together-300x169.jpg 300w, https:\/\/ruidapacking.com\/wp-content\/uploads\/2026\/11\/Sticky-Capsules-Stuck-Together-768x432.jpg 768w, https:\/\/ruidapacking.com\/wp-content\/uploads\/2026\/11\/Sticky-Capsules-Stuck-Together-18x10.jpg 18w\" sizes=\"(max-width: 960px) 100vw, 960px\" \/><\/figure>\n<\/div>\n\n\n<h2 class=\"wp-block-heading\">1. Where Do Capsule Sticking Problems Occur?<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">The location of the problem can reveal its likely cause. Empty capsules sticking together during storage require a different investigation from those adhering to a hopper or clumping in a collection bin after filling. By tracing each incident to its production stage, QA teams can separate storage-related capsule defects from capsule feeding problems and issues arising during downstream handling. This makes it easier to determine why do capsules stick together at one stage while remaining unaffected at another.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">During Storage<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">During storage of capsules, empty shells may stick together when exposed to moisture, heat, or humid air after opening. Finished products may also show capsules sticking together in a bottle due to interactions between the powder formulation and storage conditions. Since empty capsules sticking together before filling and filled capsules sticking together after packaging may have different causes, each situation should be investigated separately.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Damaged seals, frequent opening, and temperature changes can further increase the risk of capsules sticking together during storage. <\/p>\n\n\n\n<h3 class=\"wp-block-heading\">During Capsule Feeding<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">On a production line, capsules sticking to the hopper can interrupt the supply of shells to the next station. Other capsules sticking to the filling machine may cling to capsule dispensing unit and mold holes. These sticky capsules can affect the capsule feeding mechanism and capsule orientation mechanism, making it harder to load shells consistently into the segments.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">If the shells do not reach the correct position, the issue may appear later as <a href=\"https:\/\/ruidapacking.com\/ru\/capsule-shell-separation-failure\/\">capsule separation problems<\/a> or intermittent machine pickup. <\/p>\n\n\n\n<h3 class=\"wp-block-heading\">After Capsule Filling<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">After filling, capsules sticking together may become visible in a capsule collection bin, transfer chute, or polisher. Powder on the outside of the shell, warm product, static charge, or a container that adds charge during handling can all contribute. This is one reason that capsule handling problems should be reviewed across the complete capsule filling process, not only at the point where the first clump is noticed.<\/p>\n\n\n<div class=\"wp-block-image\">\n<figure class=\"aligncenter size-full\"><img decoding=\"async\" width=\"960\" height=\"540\" src=\"https:\/\/ruidapacking.com\/wp-content\/uploads\/2026\/11\/Capsules-Sticking-Together-in-a-Bottle.jpg\" alt=\"Capsules Sticking Together in a Bottle\" class=\"wp-image-18651\" srcset=\"https:\/\/ruidapacking.com\/wp-content\/uploads\/2026\/11\/Capsules-Sticking-Together-in-a-Bottle.jpg 960w, https:\/\/ruidapacking.com\/wp-content\/uploads\/2026\/11\/Capsules-Sticking-Together-in-a-Bottle-300x169.jpg 300w, https:\/\/ruidapacking.com\/wp-content\/uploads\/2026\/11\/Capsules-Sticking-Together-in-a-Bottle-768x432.jpg 768w, https:\/\/ruidapacking.com\/wp-content\/uploads\/2026\/11\/Capsules-Sticking-Together-in-a-Bottle-18x10.jpg 18w\" sizes=\"(max-width: 960px) 100vw, 960px\" \/><\/figure>\n<\/div>\n\n\n<h2 class=\"wp-block-heading\">2. Why Do Capsules Stick Together?<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Why do capsules stick together? There is rarely a single explanation. The problem can occur even when capsule shells pass incoming inspection and show no visible defects. In most cases, several factors are involved, including shell condition, ambient humidity, fill formulation, and contact surfaces. To narrow down capsule sticking problems, manufacturers should examine three main sectors separately: moisture-related stickiness, static electricity, and powder residue.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">High Humidity and Moisture Absorption<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\"><a href=\"https:\/\/ruidapacking.com\/ru\/types-of-capsules-guide\/\">Hard gelatin shells<\/a> naturally absorb and release moisture depending on their surroundings. When RH increases, moisture absorption in gelatin capsules may rise, leaving the shells softer and less resistant to deformation. Excessive moisture can contribute to capsule shell softening, surface tackiness, and gelatin capsule stickiness. <\/p>\n\n\n\n<p class=\"wp-block-paragraph\">A 2014 study in AAPS PharmSciTech reported that hard gelatin capsules stored at 15\u201325\u00b0C and 35\u201365% RH generally maintained 13\u201316% moisture. The researchers emphasizes the influence of storage and handling. These findings offer a reference for defining hard gelatin capsule storage conditions and relative humidity for capsule storage, although supplier specifications should take priority. <\/p>\n\n\n\n<p class=\"has-text-align-center wp-block-paragraph\">Table 1-Different Capsule Types on Moisture-Related Behavior<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table><tbody><tr><th>Capsule shell type<\/th><th>Moisture-related behavior<\/th><th class=\"has-text-align-center\" data-align=\"center\">What manufacturers should check<\/th><\/tr><tr><td>Hard gelatin<\/td><td>Typically 13\u201316% moisture<\/td><td class=\"has-text-align-center\" data-align=\"center\">Storage RH, exposure time, fill compatibility<\/td><\/tr><tr><td>HPMC\/Vegetarian Capsules<\/td><td>Generally lower moisture than gelatin<\/td><td class=\"has-text-align-center\" data-align=\"center\">Supplier data, static behavior, and performance on the target filler.<\/td><\/tr><tr><td>Enteric capsules \/ coated shells<\/td><td>Depends on polymer and coating type<\/td><td class=\"has-text-align-center\" data-align=\"center\">Coating specifications, storage limits, formulation compatibility<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">Temperature and RH should be monitored together. A Fagron operating manual recommends 40\u201360% RH at 15\u201325\u00b0C for its capsule-filling system, but these values should not be treated as universal limits. Manufacturers should assess temperature effects on capsule shells and capsule moisture absorption control according to supplier specifications and actual production conditions.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Static Electricity and Low Humidity<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Low humidity can cause sticking through a different mechanism. When moisture levels are low, static charges are less easily dissipated from insulating surfaces. As capsules rub against each other or come into contact with plastic bags, liners, hoppers, and feed channels, electrical charges may build up. This capsule static electricity can create an electrostatic charge on capsules, leading to electrostatic attraction between capsules or adhesion to equipment surfaces.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Fagron\u2019s manual reports noticeable static buildup below 40% RH, becoming more apparent below 30% RH in its operating conditions. Interestingly, filled HPMC capsules carried more charge than gelatin capsules under the tested conditions. This shows that HPMC capsule sticking should not be overlooked. <\/p>\n\n\n<div class=\"wp-block-image\">\n<figure class=\"aligncenter size-full\"><img decoding=\"async\" width=\"960\" height=\"540\" src=\"https:\/\/ruidapacking.com\/wp-content\/uploads\/2026\/11\/Empty-Vegetarian-Capsules.jpg\" alt=\"Empty Vegetarian Capsules\" class=\"wp-image-18652\" srcset=\"https:\/\/ruidapacking.com\/wp-content\/uploads\/2026\/11\/Empty-Vegetarian-Capsules.jpg 960w, https:\/\/ruidapacking.com\/wp-content\/uploads\/2026\/11\/Empty-Vegetarian-Capsules-300x169.jpg 300w, https:\/\/ruidapacking.com\/wp-content\/uploads\/2026\/11\/Empty-Vegetarian-Capsules-768x432.jpg 768w, https:\/\/ruidapacking.com\/wp-content\/uploads\/2026\/11\/Empty-Vegetarian-Capsules-18x10.jpg 18w\" sizes=\"(max-width: 960px) 100vw, 960px\" \/><\/figure>\n<\/div>\n\n\n<h3 class=\"wp-block-heading\">Formulation and Powder Residue<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">The fill formulation can also contribute to sticking, even when empty shells show no defects. <a href=\"https:\/\/ruidapacking.com\/ru\/powder-flowability-pharmaceutical-manufacturing\/\">Hygroscopic powder in capsules<\/a> may absorb moisture from the surrounding air or exchange water with the shell. Plant extracts, mineral blends, and concentrated ingredients are particularly worth checking for moisture sensitivity and poor flow. A formulation trial can reveal how hygroscopic powder in capsules behaves under normal production conditions.<\/p>\n\n\n<div class=\"wp-block-image\">\n<figure class=\"aligncenter size-full\"><img loading=\"lazy\" decoding=\"async\" width=\"960\" height=\"540\" src=\"https:\/\/ruidapacking.com\/wp-content\/uploads\/2026\/11\/Powder-Residue-on-Capsule-Machine-Surface.jpg\" alt=\"Powder Residue on Capsule Machine Surface\" class=\"wp-image-18654\" srcset=\"https:\/\/ruidapacking.com\/wp-content\/uploads\/2026\/11\/Powder-Residue-on-Capsule-Machine-Surface.jpg 960w, https:\/\/ruidapacking.com\/wp-content\/uploads\/2026\/11\/Powder-Residue-on-Capsule-Machine-Surface-300x169.jpg 300w, https:\/\/ruidapacking.com\/wp-content\/uploads\/2026\/11\/Powder-Residue-on-Capsule-Machine-Surface-768x432.jpg 768w, https:\/\/ruidapacking.com\/wp-content\/uploads\/2026\/11\/Powder-Residue-on-Capsule-Machine-Surface-18x10.jpg 18w\" sizes=\"(max-width: 960px) 100vw, 960px\" \/><\/figure>\n<\/div>\n\n\n<p class=\"wp-block-paragraph\">Sometimes, the problem lies in powder residue on capsules, not the shell material. Fine particles may adhere to the outer surface through static attraction or escape from the dosing area. This powder adhesion to capsule shells can make finished products look dusty or tacky, increasing the risk of capsule shells sticking together during transfer. Check the locking station, dust collection system, and mold holes first. Record any powder residue on capsules separately during capsule production quality control.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">3. How to Identify the Root Cause of Capsule Sticking<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Before changing machine parameters, establish when the defect first appears. This simple timeline can narrow down capsule filling machine problems and distinguish them from upstream material issues. It also makes <a href=\"https:\/\/ruidapacking.com\/ru\/capsule-filling-veteran-handles-common-issues-in-auto-capsule-filling-machine\/\">capsule filling troubleshooting<\/a> more repeatable: compare unused shells from the same lot with shells that have passed through the production area, then inspect the first point where adhesion appears.<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table><tbody><tr><th>What you observe<\/th><th>Check first<\/th><\/tr><tr><td>Empty capsules stick inside an unopened pack.<\/td><td>Lot history, packaging integrity, transport temperature, and supplier storage instructions.<\/td><\/tr><tr><td>Empty capsules stick after the pack is opened.<\/td><td>Room RH and temperature, exposure time, handling method, and the storage of capsules after opening.<\/td><\/tr><tr><td>Capsules cling to a hopper or feed tube.<\/td><td>RH at the machine, grounding, plastic contact points, surface condition, and capsule grade.<\/td><\/tr><tr><td>Capsules do not orient or enter the segments consistently.<\/td><td>Capsule size, matched change parts, alignment, static charge, and the capsule hopper design.<\/td><\/tr><tr><td>Filled shells stick in a collection bin.<\/td><td>External powder, product temperature, static, bin material, and cleaning records.<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">Rather than treating all capsule defects as one problem, manufacturers should identify when and where each issue first appears. Track recurring <a href=\"https:\/\/ruidapacking.com\/ru\/capsule-filling-defects-causes-solutions\/\">capsule manufacturing defects<\/a> by batch, shift, and production stage. Problems found before filling may relate to shell quality or storage, while issues inside the filler require checks of the capsule feeding mechanism, capsule orientation mechanism, and contact surfaces. <\/p>\n\n\n\n<p class=\"wp-block-paragraph\">After dosing, attention should shift to the formulation, closing station, and capsule collection bin. A structured capsule filling troubleshooting process should also review temperature, RH, unused shell condition, and powder residue before any machine settings are changed. This helps prevent capsules sticking together during storage from being mistaken for equipment failure and makes it easier to determine why do capsules stick together at certain stages but not others. When capsules sticking together occurs intermittently, the first point of adhesion is often the most useful place to start the investigation.<\/p>\n\n\n<div class=\"wp-block-image\">\n<figure class=\"aligncenter size-full\"><img loading=\"lazy\" decoding=\"async\" width=\"960\" height=\"540\" src=\"https:\/\/ruidapacking.com\/wp-content\/uploads\/2026\/11\/powder-flowability-comparison.jpg\" alt=\"powder flowability comparison\" class=\"wp-image-18653\" srcset=\"https:\/\/ruidapacking.com\/wp-content\/uploads\/2026\/11\/powder-flowability-comparison.jpg 960w, https:\/\/ruidapacking.com\/wp-content\/uploads\/2026\/11\/powder-flowability-comparison-300x169.jpg 300w, https:\/\/ruidapacking.com\/wp-content\/uploads\/2026\/11\/powder-flowability-comparison-768x432.jpg 768w, https:\/\/ruidapacking.com\/wp-content\/uploads\/2026\/11\/powder-flowability-comparison-18x10.jpg 18w\" sizes=\"(max-width: 960px) 100vw, 960px\" \/><\/figure>\n<\/div>\n\n\n<h2 class=\"wp-block-heading\">4. How to Prevent Capsules from Sticking Together<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">It\u2019s worth noted that no single measure works for every capsule type or formulation. To prevent capsules from sticking together, manufacturers need to balance humidity control, proper storage, and equipment settings suited to the fill material. The aim is to keep capsule surfaces in good condition without excessive drying or creating additional handling difficulties.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Control Temperature and Relative Humidity<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Start with the capsule supplier\u2019s documented conditions. For conventional hard gelatin shells, published references commonly cite 15\u201325\u00b0C and 35\u201365% RH, while some equipment or handling manuals recommend narrower work-area conditions such as 40\u201360% RH. Use these as starting references only; the approved supplier specification and the finished product\u2019s stability data should set the actual limits. This is the foundation of relative humidity for capsule storage and stable hard gelatin capsule storage conditions. A written storage of capsules SOP should specify the approved range, monitoring frequency, and response when readings drift. It should also define capsule humidity controls during dispensing and filling.<\/p>\n\n\n<div class=\"wp-block-image\">\n<figure class=\"aligncenter size-full\"><img loading=\"lazy\" decoding=\"async\" width=\"960\" height=\"540\" src=\"https:\/\/ruidapacking.com\/wp-content\/uploads\/2026\/11\/workshop-environment.jpg\" alt=\"workshop environment\" class=\"wp-image-18657\" srcset=\"https:\/\/ruidapacking.com\/wp-content\/uploads\/2026\/11\/workshop-environment.jpg 960w, https:\/\/ruidapacking.com\/wp-content\/uploads\/2026\/11\/workshop-environment-300x169.jpg 300w, https:\/\/ruidapacking.com\/wp-content\/uploads\/2026\/11\/workshop-environment-768x432.jpg 768w, https:\/\/ruidapacking.com\/wp-content\/uploads\/2026\/11\/workshop-environment-18x10.jpg 18w\" sizes=\"(max-width: 960px) 100vw, 960px\" \/><\/figure>\n<\/div>\n\n\n<p class=\"wp-block-paragraph\">Monitor actual warehouse and filling-room conditions with calibrated instruments. Do not rely only on the HVAC set point: record conditions near the open capsule containers and at the machine. Under FDA cGMP, 21 CFR 211.142 requires drug products to be stored under appropriate temperature, humidity, and light conditions so quality is not affected. For component handling, 21 CFR 211.80 also calls for written procedures and storage that prevents contamination. This makes environmental monitoring part of capsule production quality control, not just a housekeeping task.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Improve Storage and Handling Practices<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Keep empty shells in their original packaging until use. Proper storage of capsules depends on controlled temperature, RH, and exposure time. Once opened, packs should be resealed promptly and protected from sunlight, hot air, and sudden temperature changes. FDA guidance also recommends limiting the time original containers remain open during sampling. These measures should be included in routine capsule storage and handling procedures, with conditions reviewed against the supplier\u2019s specifications.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">For finished products, packaging and desiccants should be selected according to formulation stability. Excessive moisture removal may affect gelatin-shell flexibility. <\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Optimize Capsule Filling Operations<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">The troubleshooting process should follow the capsule filling sequence, from material feeding to finished capsule collection.<\/p>\n\n\n\n<h4 class=\"wp-block-heading\">Capsule Feeding and Dispensing<\/h4>\n\n\n\n<p class=\"wp-block-paragraph\">The first inspection usually focuses on the capsule hopper design, mold sets, and tooling, where wear, misalignment, or powder buildup may interfere with normal feeding. Capsule feeding problems can also occur when capsule sizes do not match the feeding and orientation components.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">To maintain smooth feeding, the change parts should be selected according to the capsule size being processed. Worn tooling and misaligned components need to be corrected, while powder residues on the hopper, guide surfaces, and mold bores should be removed regularly. <\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Before routine production, a sample feeding trial should be conducted to verify that capsules move through the hopper and capsule orientation mechanism smoothly, without accumulation or sticking.<\/p>\n\n\n\n<h4 class=\"wp-block-heading\">Powder Dosing and Filling<\/h4>\n\n\n\n<p class=\"wp-block-paragraph\">The feeding system needs to match the powder&#8217;s physical properties. Powders with good flowability can generally be handled by pneumatic feeding, while poorly flowing blends that tend to clump may require an auger feeder for more controlled dosing. For highly cohesive or sticky materials, a <a href=\"https:\/\/ruidapacking.com\/ru\/capsule-filling-machine\/semi-automatic-capsule-filling-machine\/\">\u043f\u043e\u043b\u0443\u0430\u0432\u0442\u043e\u043c\u0430\u0442\u0438\u0447\u0435\u0441\u043a\u0430\u044f \u043c\u0430\u0448\u0438\u043d\u0430 \u0434\u043b\u044f \u043d\u0430\u043f\u043e\u043b\u043d\u0435\u043d\u0438\u044f \u043a\u0430\u043f\u0441\u0443\u043b<\/a> may be a better option, offering greater flexibility during material handling.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Several factors should be evaluated before choosing a dosing method, including bulk density, flowability, cohesiveness, particle characteristics, and moisture sensitivity. These properties determine how easily the powder moves through the hopper and enters the capsule body. Therefore, powder flowability in capsule filling should be assessed through practical testing rather than appearance alone.<\/p>\n\n\n<div class=\"wp-block-image\">\n<figure class=\"aligncenter size-full\"><img loading=\"lazy\" decoding=\"async\" width=\"960\" height=\"540\" src=\"https:\/\/ruidapacking.com\/wp-content\/uploads\/2026\/11\/Auger-vs-pneumatic-feeding.jpg\" alt=\"Auger vs pneumatic feeding\" class=\"wp-image-18649\" srcset=\"https:\/\/ruidapacking.com\/wp-content\/uploads\/2026\/11\/Auger-vs-pneumatic-feeding.jpg 960w, https:\/\/ruidapacking.com\/wp-content\/uploads\/2026\/11\/Auger-vs-pneumatic-feeding-300x169.jpg 300w, https:\/\/ruidapacking.com\/wp-content\/uploads\/2026\/11\/Auger-vs-pneumatic-feeding-768x432.jpg 768w, https:\/\/ruidapacking.com\/wp-content\/uploads\/2026\/11\/Auger-vs-pneumatic-feeding-18x10.jpg 18w\" sizes=\"(max-width: 960px) 100vw, 960px\" \/><\/figure>\n<\/div>\n\n\n<p class=\"wp-block-paragraph\">Before recommending an <a href=\"https:\/\/ruidapacking.com\/ru\/capsule-filling-machine\/automatic-capsule-filling-machine\/\">automatic capsule filling machine<\/a>, the manufacturer should first understand the customer&#8217;s formulation. Information about powder density, flowability, and stickiness provides a useful starting point. Clients can also send representative powder and empty capsule samples for trial runs. Different feeding configurations can then be tested to compare dosing consistency, powder residue, filling performance, and cleaning requirements. This approach helps determine the most suitable machine setup and reduces potential capsule filling machine problems during production.<\/p>\n\n\n\n<h4 class=\"wp-block-heading\">Closing, Cleaning, and Capsule Collection<\/h4>\n\n\n\n<p class=\"wp-block-paragraph\">After dosing, powder residue around the closing station and on the capsule exterior deserves attention. Powder residue on capsules may affect finished product cleanliness and increase the risk of sticking during transfer.<\/p>\n\n\n<div class=\"wp-block-image\">\n<figure class=\"aligncenter size-full\"><img loading=\"lazy\" decoding=\"async\" width=\"960\" height=\"540\" src=\"https:\/\/ruidapacking.com\/wp-content\/uploads\/2026\/11\/Wipe-the-Molds-with-Cloth.jpg\" alt=\"Wipe the Molds with Cloth\" class=\"wp-image-18656\" srcset=\"https:\/\/ruidapacking.com\/wp-content\/uploads\/2026\/11\/Wipe-the-Molds-with-Cloth.jpg 960w, https:\/\/ruidapacking.com\/wp-content\/uploads\/2026\/11\/Wipe-the-Molds-with-Cloth-300x169.jpg 300w, https:\/\/ruidapacking.com\/wp-content\/uploads\/2026\/11\/Wipe-the-Molds-with-Cloth-768x432.jpg 768w, https:\/\/ruidapacking.com\/wp-content\/uploads\/2026\/11\/Wipe-the-Molds-with-Cloth-18x10.jpg 18w\" sizes=\"(max-width: 960px) 100vw, 960px\" \/><\/figure>\n<\/div>\n\n\n<p class=\"wp-block-paragraph\">At this stage, machine grounding and installed static-control devices are also reviewed. Conductive machine frames and metal components should be connected to a suitable protective earth (PE) according to its electrical design and the facility&#8217;s local wiring system. During installation, qualified electricians should verify the grounding connection and its continuity. In some cases, additional anti-static device like ionizers or static-dissipative components may be used to reduce charge buildup. Regular checks of grounding connections and static-control devices help minimize capsule static electricity, reduce unwanted adhesion, and maintain smooth material flow throughout production.<\/p>\n\n\n<div class=\"wp-block-image\">\n<figure class=\"aligncenter size-full\"><img loading=\"lazy\" decoding=\"async\" width=\"960\" height=\"540\" src=\"https:\/\/ruidapacking.com\/wp-content\/uploads\/2026\/11\/Anti-Static-Device.jpg\" alt=\"Anti-Static Device\" class=\"wp-image-18648\" srcset=\"https:\/\/ruidapacking.com\/wp-content\/uploads\/2026\/11\/Anti-Static-Device.jpg 960w, https:\/\/ruidapacking.com\/wp-content\/uploads\/2026\/11\/Anti-Static-Device-300x169.jpg 300w, https:\/\/ruidapacking.com\/wp-content\/uploads\/2026\/11\/Anti-Static-Device-768x432.jpg 768w, https:\/\/ruidapacking.com\/wp-content\/uploads\/2026\/11\/Anti-Static-Device-18x10.jpg 18w\" sizes=\"(max-width: 960px) 100vw, 960px\" \/><\/figure>\n<\/div>\n\n\n<p class=\"wp-block-paragraph\">Finally, a controlled production trial confirms whether the selected adjustments reduce capsule defects and improve overall handling consistency.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">5. How Capsule Filling Equipment Helps Reduce Sticking Problems<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Environmental controls help reduce problems with capsules sticking together, but the right capsule filling equipment is equally important. Feeding and dosing configurations should match capsule size and powder properties to maintain smooth, consistent production.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Matching Capsule Filling Equipment to Capsule and Powder Characteristics<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">When selecting an automatic capsule filling machine, manufacturers should consider the following configurations:<\/p>\n\n\n\n<h4 class=\"wp-block-heading\">Powder Dosing Systems<\/h4>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Pneumatic feeding for well flowing powders.<\/li>\n\n\n\n<li>Auger feeding for cohesive or poorly flowing blends.<\/li>\n\n\n\n<li>Semi-automatic filling solutions for particularly sticky formulations.<\/li>\n<\/ul>\n\n\n\n<h4 class=\"wp-block-heading\">Cleaning and Powder Control<\/h4>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Dust extraction unit to clean away powder residue.<\/li>\n\n\n\n<li>Powder recovery system to collect excess filling material.<\/li>\n\n\n\n<li>Mold hole cleaning stations and air-assisted hollow locking pins to reduce powder residue.<\/li>\n\n\n\n<li>Enclosed Design with easy-to-clean contact surfaces to maintain a cleaner capsule filling process.<\/li>\n<\/ul>\n\n\n<div class=\"wp-block-image\">\n<figure class=\"aligncenter size-full\"><img loading=\"lazy\" decoding=\"async\" width=\"960\" height=\"540\" src=\"https:\/\/ruidapacking.com\/wp-content\/uploads\/2026\/11\/Capsule-Filling-Machine-Hollow-Pins-with-Air-Flow-Assist.jpg\" alt=\"Capsule Filling Machine Hollow Pins with Air-Flow Assist\" class=\"wp-image-18650\" srcset=\"https:\/\/ruidapacking.com\/wp-content\/uploads\/2026\/11\/Capsule-Filling-Machine-Hollow-Pins-with-Air-Flow-Assist.jpg 960w, https:\/\/ruidapacking.com\/wp-content\/uploads\/2026\/11\/Capsule-Filling-Machine-Hollow-Pins-with-Air-Flow-Assist-300x169.jpg 300w, https:\/\/ruidapacking.com\/wp-content\/uploads\/2026\/11\/Capsule-Filling-Machine-Hollow-Pins-with-Air-Flow-Assist-768x432.jpg 768w, https:\/\/ruidapacking.com\/wp-content\/uploads\/2026\/11\/Capsule-Filling-Machine-Hollow-Pins-with-Air-Flow-Assist-18x10.jpg 18w\" sizes=\"(max-width: 960px) 100vw, 960px\" \/><\/figure>\n<\/div>\n\n\n<h4 class=\"wp-block-heading\">Configuration Verification<\/h4>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Test the selected setup with actual capsule shells and powder samples.<\/li>\n\n\n\n<li>Verify feeding stability, dosing consistency, and cleaning performance during the <a href=\"https:\/\/ruidapacking.com\/ru\/iq-oq-pq-equipment\/\">Factory Acceptance Test<\/a>.<\/li>\n\n\n\n<li>Check whether the configuration helps reduce capsule filling machine problems and filled capsules sticking together during production.<\/li>\n<\/ul>\n\n\n\n<h3 class=\"wp-block-heading\">Ruida Packing: Customized Solutions and Technical Support for Powder Stickiness<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Since 2015, Ruida Packing has focused on pharmaceutical and nutraceutical equipment manufacturing, with over 30% of its team dedicated to R&amp;D. Our capsule-filling solutions can be configured according to capsule size, powder characteristics, dosing requirements, and cleaning needs. For projects involving electronic records, optional features include user-level access management, audit trails, electronic signatures, and MES connectivity, depending on the agreed system scope. Our equipment is designed to support cGMP-oriented production, with site-specific qualification and validation carried out by the manufacturer.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">6. Conclusion<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Capsules sticking together can begin in storage, develop during feeding, or appear after filling. High humidity may increase shell tack, while dry conditions can promote static; hygroscopic fills and surface powder add another layer to the problem. A reliable storage of capsules program therefore needs supplier-approved conditions, sealed handling, and production checks. Good storage of capsules practice can reduce the chance of sticky capsule shells reaching the line and creating further handling issues. When manufacturers ask why do capsules stick together, the best answer starts with the point where the issue appears, then follows the evidence through the material, environment, and machine.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">FAQs<\/h2>\n\n\n<div id=\"rank-math-faq\" class=\"rank-math-block\">\n<div class=\"rank-math-list\">\n<div id=\"faq-question-hard-capsules-1\" class=\"rank-math-list-item\">\n<h3 class=\"rank-math-question\">Q1: Why Do My Capsules Look Clumpy or Stick Together?<\/h3>\n<div class=\"rank-math-answer\">\n\n<p>Capsules may clump because of moisture uptake, static charge, or powder on the shell surface. Check the lot, room conditions, and handling stage before changing machine settings.<\/p>\n\n<\/div>\n<\/div>\n<div id=\"faq-question-hard-capsules-2\" class=\"rank-math-list-item\">\n<h3 class=\"rank-math-question\">Q2: Why Are Filled Capsules Sticking Together in the Bin?<\/h3>\n<div class=\"rank-math-answer\">\n\n<p>Check for powder on the outer shell, warm or humid air, static, and the bin material. Compare clean capsules with the collected batch to isolate the source.<\/p>\n\n<\/div>\n<\/div>\n<div id=\"faq-question-hard-capsules-3\" class=\"rank-math-list-item\">\n<h3 class=\"rank-math-question\">Q3: Why Do HPMC Capsules Stick to the Hopper?<\/h3>\n<div class=\"rank-math-answer\">\n\n<p>Static charge, dry air, grounding, and plastic contact surfaces can contribute. Check RH at the filler and test the actual HPMC grade with the machine setup.<\/p>\n\n<\/div>\n<\/div>\n<div id=\"faq-question-hard-capsules-4\" class=\"rank-math-list-item\">\n<h3 class=\"rank-math-question\">Q4: What Happens to Capsules in a Humid Room?<\/h3>\n<div class=\"rank-math-answer\">\n\n<p>Gelatin shells can absorb moisture, soften, swell, or become tacky. The extent depends on exposure time, temperature, capsule formulation, and the supplier\u2019s specifications.<\/p>\n\n<\/div>\n<\/div>\n<div id=\"faq-question-hard-capsules-5\" class=\"rank-math-list-item\">\n<h3 class=\"rank-math-question\">Q5: How Should Empty Capsules Be Stored to Prevent Sticking?<\/h3>\n<div class=\"rank-math-answer\">\n\n<p>Keep shells in sealed original packaging and follow the supplier\u2019s temperature and RH limits. A written storage of capsules procedure should also define how opened packs are resealed and returned to controlled storage. Reseal opened packs promptly and limit unnecessary exposure to room air.<\/p>\n\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n\n\n<h2 class=\"wp-block-heading\">\u0421\u0441\u044b\u043b\u043a\u0438<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">[1] <a href=\"https:\/\/link.springer.com\/article\/10.1208\/s12249-014-0094-y\" rel=\"nofollow noopener\" target=\"_blank\">Stegemann S, Connolly P, Matthews W, et al. Application of QbD Principles for the Evaluation of Empty Hard Capsules as an Input Parameter in Formulation Development and Manufacturing. AAPS PharmSciTech. 2014;15:542\u2013549.<\/a> <\/p>\n\n\n\n<p class=\"wp-block-paragraph\">[2] <a href=\"https:\/\/pubmed.ncbi.nlm.nih.gov\/32439451\/\" rel=\"nofollow noopener\" target=\"_blank\">Yang N, Chen H, Jin Z, et al. Moisture sorption and desorption properties of gelatin, HPMC and pullulan hard capsules. International Journal of Biological Macromolecules. 2020;159:659\u2013666.<\/a> <\/p>\n\n\n\n<p class=\"wp-block-paragraph\">[3] <a href=\"https:\/\/pubmed.ncbi.nlm.nih.gov\/40194598\/\" rel=\"nofollow noopener\" target=\"_blank\">Stankovic-Brandl M, Zellnitz-Neugebauer S, Wutscher T, et al. Filling process-induced tribo-charging of lubricated and non-lubricated gelatine and HPMC capsules. 2025.<\/a> <\/p>\n\n\n\n<p class=\"wp-block-paragraph\">[4] <a href=\"https:\/\/fagron.de\/wp-content\/uploads\/2021\/06\/1406_CC-Gebrauchsanleitung_EN-1.pdf\" rel=\"nofollow noopener\" target=\"_blank\">Fagron. CapsiCards\u00ae System \u2013 Operating Manual, Environmental Conditions and Capsule Performance.<\/a> <\/p>","protected":false},"excerpt":{"rendered":"<p>When capsules stick together, is humidity the only culprit? Discover how moisture, static electricity, powder, and machine lead to capsule sticking and how to solve it.<\/p>","protected":false},"author":4,"featured_media":18655,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"_sitemap_exclude":false,"_sitemap_priority":"","_sitemap_frequency":"","footnotes":""},"categories":[35],"tags":[135,340],"class_list":["post-18645","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-blog","tag-capsule-filling","tag-hard-capsules"],"acf":[],"_links":{"self":[{"href":"https:\/\/ruidapacking.com\/ru\/wp-json\/wp\/v2\/posts\/18645","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/ruidapacking.com\/ru\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/ruidapacking.com\/ru\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/ruidapacking.com\/ru\/wp-json\/wp\/v2\/users\/4"}],"replies":[{"embeddable":true,"href":"https:\/\/ruidapacking.com\/ru\/wp-json\/wp\/v2\/comments?post=18645"}],"version-history":[{"count":14,"href":"https:\/\/ruidapacking.com\/ru\/wp-json\/wp\/v2\/posts\/18645\/revisions"}],"predecessor-version":[{"id":18669,"href":"https:\/\/ruidapacking.com\/ru\/wp-json\/wp\/v2\/posts\/18645\/revisions\/18669"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/ruidapacking.com\/ru\/wp-json\/wp\/v2\/media\/18655"}],"wp:attachment":[{"href":"https:\/\/ruidapacking.com\/ru\/wp-json\/wp\/v2\/media?parent=18645"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/ruidapacking.com\/ru\/wp-json\/wp\/v2\/categories?post=18645"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/ruidapacking.com\/ru\/wp-json\/wp\/v2\/tags?post=18645"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}